Results 1 - 15 of about 459 sawaal for "jumper"
toolkit. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original position. On the computer motherboard locate and remove the CMOS battery for at least 10 minutes allowing
Posted in
Computers & Technology by jks marven at 7:12 PM on May 08, 2008
motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original position. The location of the jumpers or dipswitches may vary; however, here are general locations where these jumpers / dipswitch may
Posted in
Computers & Technology by madhuhot at 12:59 AM on October 27, 2007
BIOS Security and Maintenance toolkit, which is available by clicking here. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original position. The location of the jumpers
Posted in
Computers & Technology by madhuhot at 5:33 PM on October 26, 2007
utility to decrypt / bypass BIOS passwords is the PC BIOS Security and Maintenance toolkit, which is available by clicking here. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its
Posted in
Computers & Technology by comp at 5:33 PM on October 26, 2007
On the edge of the motherboard - Most jumpers are located on the side of the motherboard for easy accessibility, verify by looking at all visible edges of the motherboard. By the CMOS battery - Some manufactures will place the jumper to clear the CMOS / BIOS password by the actual CMOS battery. By the processor - Some manufactures will place the jumpers by the processor of the computer. However, note
Posted in
Computers & Technology by Anju at 11:16 AM on November 01, 2007
socket. Then locate the CMOS jumper it looks like a small plastic thingy on 2 pins with 1 pin beside it, within a 1" of the battery. If youre having trouble looking for it, look in the motherboard manual. After you have found it, carefuly pull straight up on it, and place it on the 2-3 pinsit was on the 1-2 pins. With the battery removed and the jumper moved, turn the computer on, and check to see
Posted in
Computers & Technology by Pritesh at 11:48 PM on September 12, 2008
socket. Then locate the CMOS jumper it looks like a small plastic thingy on 2 pins with 1 pin beside it, within a 1" of the battery. If youre having trouble looking for it, look in the motherboard manual. After you have found it, carefuly pull straight up on it, and place it on the 2-3 pinsit was on the 1-2 pins. With the battery removed and the jumper moved, turn the computer on, and check to see
Posted in
Computers & Technology by Sonam Kalra at 3:30 AM on August 11, 2008
steps :1 Open the case and than take out the BIOS back-up battery.2 Than you need to keep it out for a longer period to change the BIOS Jumper to clear the BIOS.3 You need to put the jumper back BIOS settings from the default to custom settings...steps :1 Open the case and than take out the BIOS back-up battery.2 Than you need to keep it out for a longer period to change the BIOS Jumper to clear
Posted in
Computers & Technology by Harish at 7:57 PM on July 01, 2008
A jumper is an electrically conductive component that you place over pairs of pins to connect them electronically. For example, a jumper is one way to designate a hard drive as master or slave....In a computer, a jumper is a pair of prongs that are electrical contact points set into the computer motherboard or an adapter card. When you set a jumper, you place a plug on the prongs that completes a contact
Posted in
Computers & Technology by Rohan at 11:51 AM on November 10, 2007
by clicking here. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original position. The location of the jumpers or dipswitches may vary; however, here are general locations where
Posted in
Computers & Technology by Rocky at 5:09 AM on November 13, 2007
to decrypt / bypass BIOS passwords is the PC BIOS Security and Maintenance toolkit, which is available by clicking here. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original
Posted in
Computers & Technology by mary at 7:13 AM on October 31, 2007
to decrypt / bypass BIOS passwords is the PC BIOS Security and Maintenance toolkit, which is available by clicking here. On the computer motherboard locate the BIOS clear / password jumper or dipswitch and change its position. Once this jumper has been changed, turn on the computer and the password should be cleared. Once cleared, turn the computer off and return the jumper or dipswitch to its original
Posted in
Computers & Technology by comp at 7:13 AM on October 31, 2007
.Follow your instructions on how to correctly open your enclosure.Set your HDD to the Master setting or Master/No Slave if one exists. This jumper setting is located between the Molex power connector 4 large round pins and the ATA/SATA connector. You will see 2 rows of four or five small pins, and a small clipjumper connected to 2 of them. Pull out the jumper with a tool such as tweezers or a pencil
Posted in
Computers & Technology by Ravi Gupta at 3:37 PM on July 20, 2008
and connect it to the HD. Next, connect the IDE interface cable to your HD.5 Now, time to Set the tricky drive jumper. If youve installed your hard drive on the primary IDE channel as a second drive and its sharing a cable with the your current drive, you need to designate your new drive as the Slave drive. However, if your new drive is going to be used as your PCs new boot drive, you want to set the jumper
Posted in
Computers & Accessories by jai at 1:45 AM on June 11, 2008
A jumper is a small connector that connects two pins together to complete a circuit. Jumpers are used inside a computer to do several things.e.g. Hard drives use jumpers to tell the computer which drive is the master drive and which is the slave.computers BIOS that holds basic settings uses a jumper to erase the settings as well....Mukesh,jumper In a computer, a jumper is a pair of prongs
Posted in
Computers & Technology by Mukesh at 11:40 AM on February 09, 2008
