what is differance between hub and switch?  

anil Hubs, switches, and routers are all devices which let you connect one or more computers to other computers, networked devices, or to other networks. Each has two or more connectors called ports into which you plug in the cables to make the connection. Varying degrees of magic happen inside the device, and therein lies the difference. I often see the terms misused so let's clarify what each one really means.

•

A hub is typically the least expensive, least intelligent, and least complicated of the three. Its job is very simple: anything that comes in one port is sent out to the others. That's it. Every computer connected to the hub "sees" everything that every other computer on the hub sees. The hub itself is blissfully ignorant of the data being transmitted. For years, simple hubs have been quick and easy ways to connect computers in small networks.

A switch does essentially what a hub does but more efficiently. By paying attention to the traffic that comes across it, it can "learn" where particular addresses are. For example, if it sees traffic from machine A coming in on port 2, it now knows that machine A is connected to that port and that traffic to machine A needs to only be sent to that port and not any of the others. The net result of using a switch over a hub is that most of the network traffic only goes where it needs to rather than to every port. On busy networks this can make the network significantly faster
this is taken from source http://ask-leo.com/whats_the_differ ence_between_a_hub_a_switch_and_a_r outer.html

Answered by laks at 4:47 PM on May 15, 2008

Well,

A hub or concentrator is a device for connecting multiple twisted pair or fiber optic Ethernet devices together, making them act as a single network segment.

Hubs work at the physical layer (layer 1) of the OSI model, and the term layer 1 switch is often used interchangeably with hub.

The device is thus a form of multiport repeater. Network hubs are also responsible for forwarding a jam signal to all ports if it detects a collision.

A switch is a computer networking device that connects network segments.

switches are capable of inspecting data packets as they are received, determining the source and destination device of that packet, and forwarding it appropriately.

By delivering each message only to the connected device it was intended for, a network switch conserves network bandwidth and offers generally better performance than a hub.

Answered by ajay kumar at 5:32 AM on May 12, 2008

well, The term ‘hub’ is sometimes used to refer to any piece of network equipment that connects PCs together, but it actually refers to a multi-port repeater. This type of device simply passes on (repeats) all the information it receives, so that all devices connected to its ports receive that information.A hub is typically the least expensive, least intelligent, and least complicated of the three. Its job is very simple: anything that comes in one port is sent out to the others. That's it. Every computer connected to the hub "sees" everything that every other computer on the hub sees. The hub itself is blissfully ignorant of the data being transmitted. For years, simple hubs have been quick and easy ways to connect computers in small networks.

A switch does essentially what a hub does but more efficiently. By paying attention to the traffic that comes across it, it can "learn" where particular addresses are. For example, if it sees traffic from machine A coming in on port 2, it now knows that machine A is connected to that port and that traffic to machine A needs to only be sent to that port and not any of the others. The net result of using a switch over a hub is that most of the network traffic only goes where it needs to rather than to every port. On busy networks this can make the network significantly faster.

Answered by Saurabh at 10:56 PM on May 05, 2008

hub will just forwords packets blindly throug out the network and it is just a repeater..
but switch have a tendency to send the packet only to the destination system....
hence there is no chance for data collession......

Answered by muralidhar at 10:06 PM on May 05, 2008

hi anil:-
A hub is typically the least expensive, least intelligent, and least complicated of the three. Its job is very simple: anything that comes in one port is sent out to the others. That's it. Every computer connected to the hub "sees" everything that every other computer on the hub sees. The hub itself is blissfully ignorant of the data being transmitted. For years, simple hubs have been quick and easy ways to connect computers in small networks.

A switch does essentially what a hub does but more efficiently. By paying attention to the traffic that comes across it, it can "learn" where particular addresses are. For example, if it sees traffic from machine A coming in on port 2, it now knows that machine A is connected to that port and that traffic to machine A needs to only be sent to that port and not any of the others. The net result of using a switch over a hub is that most of the network traffic only goes where it needs to rather than to every port. On busy networks this can make the network significantly faster.

Answered by shepherd at 6:59 PM on May 05, 2008

Hubs and switches are different types of network equipment that connect devices. They differ in the way that they pass on the network traffic that they receive.
Hubs, switches, and routers are all devices which let you connect one or more computers to other computers, networked devices, or to other networks. Each has two or more connectors called ports into which you plug in the cables to make the connection. Varying degrees of magic happen inside the device, and therein lies the difference. I often see the terms misused so let's clarify what each one really means.
A hub is typically the least expensive, least intelligent, and least complicated of the three. Its job is very simple: anything that comes in one port is sent out to the others. That's it. Every computer connected to the hub "sees" everything that every other computer on the hub sees. The hub itself is blissfully ignorant of the data being transmitted. For years, simple hubs have been quick and easy ways to connect computers in small networks.

A switch does essentially what a hub does but more efficiently. By paying attention to the traffic that comes across it, it can "learn" where particular addresses are. For example, if it sees traffic from machine A coming in on port 2, it now knows that machine A is connected to that port and that traffic to machine A needs to only be sent to that port and not any of the others. The net result of using a switch over a hub is that most of the network traffic only goes where it needs to rather than to every port. On busy networks this can make the network significantly faster.

A router is the smartest and most complicated of the bunch. Routers come in all shapes and sizes from the small four-port broadband routers that are very popular right now to the large industrial strength devices that drive the internet itself. A simple way to think of a router is as a computer that can be programmed to understand, possibly manipulate, and route the data its being asked to handle. For example, broadband routers include the ability to "hide" computers behind a type of firewall which involves slightly modifying the packets of network traffic as they traverse the device. All routers include some kind of user interface for configuring how the router will treat traffic. The really large routers include the equivalent of a full-blown programming language to describe how they should operate as well as the ability to communicate with other routers to describe or determine the best way to get network traffic from point A to point B.

A quick note on one other thing that you'll often see mentioned with these devices and that's network speed. Most devices now are capable of both 10mps (10 mega-bits, or million bits, per second) as well as 100mbs and will automatically detect the speed. If the device is labeled with only one speed then it will only be able to communicate with devices that also support that speed. 1000mbs or "gigabit" devices are starting to slowly become more common as well. Similarly many devices now also include 802.11b or 802.11g wireless transmitters that simply act like additional ports to the device.

Source :

http://ask-leo.com/w hats_the_difference_between_a_ hub_a_switch_and_a_router.html

Answered by Smarty at 5:31 PM on May 05, 2008

anil Although hubs and switches both glue the PCs in a network together, a switch is more expensive and a network built with switches is generally considered faster than one built with hubs. Why?

When a hub receives a packet (chunk) of data (a frame in Ethernet lingo) at one of its ports from a PC on the network, it transmits (repeats) the packet to all of its ports and, thus, to all of the other PCs on the network. If two or more PCs on the network try to send packets at the same time a collision is said to occur. When that happens all of the PCs have to go though a routine to resolve the conflict. The process is prescribed in the Ethernet Carrier Sense Multiple Access with Collision Detection (CSMA/CD) protocol. Each Ethernet Adapter has both a receiver and a transmitter. If the adapters didn't have to listen with their receivers for collisions they would be able to send data at the same time they are receiving it (full duplex). Because they have to operate at half duplex (data flows one way at a time) and a hub retransmits data from one PC to all of the PCs, the maximum bandwidth is 100 Mhz and that bandwidth is shared by all of the PC's connected to the hub. The result is when a person using a computer on a hub downloads a large file or group of files from another computer the network becomes congested. In a 10 Mhz 10Base-T network the affect is to slow the network to nearly a crawl. The affect on a small, 100 Mbps (million bits per scond), 5-port network is not as significant.





Two computers can be connected directly together in an Ethernet with a crossover cable. A crossover cable doesn't have a collision problem. It hardwires the Ethernet transmitter on one computer to the receiver on the other. Most 100BASE-TX Ethernet Adapters can detect when listening for collisions is not required with a process known as auto-negotiation and will operate in a full duplex mode when it is permitted. The result is a crossover cable doesn't have delays caused by collisions, data can be sent in both directions simultaneously, the maximum available bandwidth is 200 Mbps, 100 Mbps each way, and there are no other PC's with which the bandwidth must be shared.

An Ethernet switch automatically divides the network into multiple segments, acts as a high-speed, selective bridge between the segments, and supports simultaneous connections of multiple pairs of computers which don't compete with other pairs of computers for network bandwidth. It accomplishes this by maintaining a table of each destination address and its port. When the switch receives a packet, it reads the destination address from the header information in the packet, establishes a temporary connection between the source and destination ports, sends the packet on its way, and then terminates the connection.

Picture a switch as making multiple temporary crossover cable connections between pairs of computers (the cables are actually straight-thru cables; the crossover function is done inside the switch). High-speed electronics in the switch automatically connect the end of one cable (source port) from a sending computer to the end of another cable (destination port) going to the receiving computer on a per packet basis. Multiple connections like this can occur simultaneously. It's as simple as that. And like a crossover cable between two PCs, PC's on an Ethernet switch do not share the transmission media, do not experience collisions or have to listen for them, can operate in a full-duplex mode, have bandwidth as high as 200 Mbps, 100 Mbps each way, and do not share this bandwidth with other PCs on the switch. In short, a switch is "more
for more inf check source http://www.duxcw.com/faq/network/hu bsw.htm

Answered by raj u at 3:29 PM on May 05, 2008

Hub is a network, a device that connects nodes and servers together at a central point. switch is a networking device that learns which machine is connected to its port by using the device's IP address

Answered by Nishu's at 12:01 PM on May 05, 2008

A hub or concentrator is a device for connecting multiple twisted pair or fiber optic Ethernet devices together, making them act as a single network segment. Hubs work at the physical layer (layer 1) of the OSI model, and the term layer 1 switch is often used interchangeably with hub. The device is thus a form of multiport repeater. Network hubs are also responsible for forwarding a jam signal to all ports if it detects a collision.

A switch is a computer networking device that connects network segments.
switches are capable of inspecting data packets as they are received, determining the source and destination device of that packet, and forwarding it appropriately. By delivering each message only to the connected device it was intended for, a network switch conserves network bandwidth and offers generally better performance than a hub.

Answered by Hem@nt at 10:43 AM on May 05, 2008

well Anil, Hubs and switches are different types of network equipment that connect devices. They differ in the way that they pass on the network traffic that they receive.
Hubs, switches, and routers are all devices which let you connect one or more computers to other computers, networked devices, or to other networks. Each has two or more connectors called ports into which you plug in the cables to make the connection. Varying degrees of magic happen inside the device, and therein lies the difference. I often see the terms misused so let's clarify what each one really means.
A hub is typically the least expensive, least intelligent, and least complicated of the three. Its job is very simple: anything that comes in one port is sent out to the others. That's it. Every computer connected to the hub "sees" everything that every other computer on the hub sees. The hub itself is blissfully ignorant of the data being transmitted. For years, simple hubs have been quick and easy ways to connect computers in small networks.

A switch does essentially what a hub does but more efficiently. By paying attention to the traffic that comes across it, it can "learn" where particular addresses are. For example, if it sees traffic from machine A coming in on port 2, it now knows that machine A is connected to that port and that traffic to machine A needs to only be sent to that port and not any of the others. The net result of using a switch over a hub is that most of the network traffic only goes where it needs to rather than to every port. On busy networks this can make the network significantly faster.

A router is the smartest and most complicated of the bunch. Routers come in all shapes and sizes from the small four-port broadband routers that are very popular right now to the large industrial strength devices that drive the internet itself. A simple way to think of a router is as a computer that can be programmed to understand, possibly manipulate, and route the data its being asked to handle. For example, broadband routers include the ability to "hide" computers behind a type of firewall which involves slightly modifying the packets of network traffic as they traverse the device. All routers include some kind of user interface for configuring how the router will treat traffic. The really large routers include the equivalent of a full-blown programming language to describe how they should operate as well as the ability to communicate with other routers to describe or determine the best way to get network traffic from point A to point B.

A quick note on one other thing that you'll often see mentioned with these devices and that's network speed. Most devices now are capable of both 10mps (10 mega-bits, or million bits, per second) as well as 100mbs and will automatically detect the speed. If the device is labeled with only one speed then it will only be able to communicate with devices that also support that speed. 1000mbs or "gigabit" devices are starting to slowly become more common as well. Similarly many devices now also include 802.11b or 802.11g wireless transmitters that simply act like additional ports to the device.

For more details you can visit the gollowing links:

http://ask-leo.com/w hats_the_difference_between_a_ hub_a_switch_and_a_router.html

http://www.duxcw.com/faq/n etwork/hubsw.htm

http://www .darron.net/network/secondpage .html

Answered by Uttam at 10:39 PM on May 04, 2008