DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by R.P. Singh , an ibibo Master, at 8:22 PM on July 22, 2008

DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Rocky , an ibibo Master, at 10:56 AM on July 22, 2008

DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by .... ..... , an ibibo Master, at 8:57 AM on July 15, 2008

DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Raksha , an ibibo Master, at 8:48 AM on July 15, 2008

DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Sharad Singh , an ibibo Master, at 6:27 PM on July 14, 2008

well, ~DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Ni .. , an ibibo Master, at 8:16 PM on July 13, 2008

well, ~DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Satya ~ , an ibibo Master, at 5:30 PM on July 11, 2008

well, DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Romi , an ibibo Master, at 11:14 AM on July 09, 2008

~DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Shobhit , an ibibo Master, at 3:16 PM on July 01, 2008

~DC DRIVE (optional)

(1.5 HP, 220 volt 1 phase)

DC motors can rotate a workpiece at very low RPM's, but the spindle torque will be very low compared to running the motor faster. Consequently we utilize a compound belt reduction, in combination with the DC motor/controller, to provide very high torque at very low speeds. 5/8", "B" section Vee Belts are used for very effective power transmission.

The DC motor controller (mounted on the pendant) features a rotary speed control dial, spindle reversing switch and motor brake. Speed range is from 0 to 425 in the low range and 0 to 2520 in the high range. LATHE SPINDLE

The spindle is 1-1/4" diameter, supported by three (3) sealed for life ball bearings. Thread size is 1-1/4"-8 tpi.

Answered by Gyan Singh , an ibibo Master, at 2:24 PM on June 30, 2008